What gun lube do you use?

[Descreet38]

Just curious as to what everyone is using and how you rate the performance.

Personally I use Miltech-1 both oil and grease. Performance is outstanding. Only (small) drawback is the procedures for initial application and then heating it up. Even with that you will find it is an absolute great lubrication system for any weapon system.

On one of my Beretta 92's I use in competition I have went over 750 rounds in a single day with no further lube and NO issues.

[Bman505]

Do you have to heat the lube up?
I could be wrong, I use solvent every now and then when cleaning my pistols and then go back over it with gun oil. Do you use solvent when cleaning your firearms?

[Descreet38]

Bman - actually you can use a heat source but the tried and true method is to apply and then shoot a lot - then repeat.

here are the miltec basic instructions.

INITIAL TREATMENT: Applying MILITEC-1 to a firearm for the first time is a two-step process: (1) Application and (2) Firing.

STEP ONE: APPLICATION. Now that the firearm is clean and dry, apply a light film of MILITEC-1 to all surfaces, including the bore. Burnish/polish MILITEC-1 into exterior surfaces by rubbing rapidly using a cloth lightly dampened with MILITEC-1. Sparingly apply drops into the action, concentrating on springs, moving parts and metal-to-metal contact areas. If your firearm has a magazine, be sure to apply MILITEC-1 both inside and out. Leave a very light film of MILITEC-1 on all surfaces during reassembly. Now proceed to Step Two.

STEP TWO: FIRING. Once you fire your weapon enough times to reach operating temperatures, the heat and friction will activate MILITEC-1, strengthening the bonding process that was started in Step One. While firing, MILITEC-1 creates a self-lubricating, water-repelling, dry compound within the gunmetal.

Additional Application Instructions: If Step Two is not immediately possible, consider applying low heat to the firearm to facilitate the bonding process until you can perform Step Two. In field conditions, place your lubed firearm in the sun underneath black plastic or a similar ventilated heat source for at least two hours. Alternatively, you may use a heat gun, hairdryer, burnishing or polishing tool to heat the gunmetal. In heat controlled environments, do not exceed 150° F (65° C). In all applications that require heat to condition the firearm, always insure proper ventilation and wear protective clothing. Please consult our MSDS (http://www.militec1.com/msds1.html) for additional information.

ULTIMATE PROTECTION: To maximize the effects of MILITEC-1, repeat Step One and Step Two while the firearm is still hot from the first firing session. MILITEC-1's impregnated molecular bond intensifies during the next 2-3 applications on hot gunmetal. MILITEC-1 has now become a physical part of the gunmetal.

SUBSEQUENT APPLICATIONS: It is important to continue using MILITEC-1 to lubricate your firearm throughout its normal service life. Consistent use of MILITEC-1 will maintain the self-lubricating effect, maximize corrosion protection, and minimize wear on all friction surfaces. Fouling, deposits and metallic debris do not adhere as easily to gunmetal surfaces conditioned with MILITEC-1. Use a safe, inexpensive cleaner or solvent to detail the firearm, if necessary. For maximum corrosion protection, and especially if long-term storage is anticipated, leave a very light film of MILITEC-1 on all surfaces, after both steps or field application procedures are completed

[Scooter]

I've been using TriFlow for about 12 years now and love it. I will be honest though, I might have to give MILITECH a try after reading your experience. Where I can I find it at and what does it cost on average?

[Jkwas]

I use Rem oil or break free depending on how heavy I want to lube.

[Descreet38]

for government employees or military (including retirees)
http://www.militec1.com/miva/merchant.mvc?Screen=CTGY&Store_Code=militec1&Category_Code=mil

For normal retail

http://www.militec1.com/miva/merchant.mvc?Screen=CTGY&Store_Code=militec1&Category_Code=1

[Grampa]

How come I can only pick one? I use Gun Butter on my semi-autos and FP-10 on my rifles and shotguns. No real reason, just the FP-10 is in an aerosol and I can spray into the hard to reach places, let it run in and out, then wipe off the excess.

[MP3Mogul]

I use RiG grease in combination with RemOil on all my guns... never had any problems, no matter what temp.

[rtuck77]

I just put militec-1 on my 92fs I did it by heating it up with a hair dyer cause I dont have the ammo or the money to buy enough ammo to do it the old fashen way (shooting alot)

[tblt44]

I use hoppe's but I voted for hpooes because that was the closes thing on your list.I know its a very bad typo

[Descreet38]

Read the Glock vs. Beretta for further testimony of Miltech-1. If I didn't believe in it before I sure do now.

http://www.concealcarrychat.com/forums/showthread.php?t=279

[showags]

I voted for CLP but actually prefer the Breakfree LP for the actual lube. I use CLP for the cleaning. The LP comes in a smaller, non-aerosol squeeze bottle with a 4 inch 'straw'. It is a higher solids formula and I am able to more precisely lube the parts I want to without the worry of over oiling. I use this on all of my weapons(rifles, semi-auto shotguns, and pistols).

[sinclair]

Well, that Militec-1 stuff was looking good when I first reviewed this:

http://www.laniganperformance.com/faq.html

But my suspicion was aroused when there is no reference to coastal conditions. I have spent a bit of time around the gulf coast and that is not a good place for guns and corrosion. With that in mind, I came across this little goodie:

The Salt Water Corrosion Test, and a very interesting result for Descreet38. Note that of the 12 lubricants tested the Militec stuff came in almost dead last. (11th place)

http://www.slip2000.com/saltwatertest.html

I use Balistrol after Bore Butter, because of its desiccant qualities. Although it only comes in 5th on the above test, its desiccant qualities were well oversaturated in that test. (It can absorb a significant percent of its weight in moisture but loses out when saturated) Its useful for many other applications as well. Still, the saltwater test is worth noting and I think I will obtain some of this Slip 2000 stuff. That was a rather harsh test for protective oils. Says a lot for Slip 2000, the number one pole position.

[goneballistic]

I use Ballistol on exterior metal surfaces and Slip2000 in the bore. Using Slip2000 makes for easier cleaning after shooting, especially in heavy fouling, overbore rifle calibers.

[Tucson]

And I'm the odd man out who used Castrol synthetic blend 5w-30.
It works very well, holds up longer than most gun oils, which tend to be thin, and cost a lot less than your typical gun oils. I haven't found a reason not to use it.

[Sam]

Personally I use the original synthetic blend CLP. It works wonderfully in all applications, meets the milspec for CLP type fluids being suitable per DoD for all small arms with the exception of 2 specialized applications in the M134.

It is called DEXRON

[Old Hick]

Yes, this thread is over a year old, but I'm new here so I will chime in.

I use Eezox as cleaner-lube, and then Brian Enos Slide Glide where any grease is needed, i.e. slide rails etc....

I used Hoppies and Rem oil for years, but since I tried the Eezox, I will never use anything else.

Stay Safe.

[Learn2turn]

Mobil 15/50w